Skip to content
RSS feed for this category

Paint coating equipment

Standards in development (170)

Sort by: Title | Status

Standard TitleStatus
BS EN 00271062 Plating and anodizing lines - safety requirementsAccepted
BS EN 13765 Thermoplastic multi-layer (non-vulcanized) hoses and hose assemblies for the transfer of hydrocarbons, solvents and chemicals - SpecificationIdea
BS EN 13766 Thermoplastic multi-layer (non-vulcanized) hoses and hose assemblies for the transfer of liquid petroleum gas and liquefied natural gas - SpecificationIdea
BS EN 14420-8:2013/A1 Hose fittings with clamp units Part 8: Symmetrical half coupling (Guillemin system)/Amendment 1Approval
Opens a new windowBS EN 14423:2013/A1 Clamp type coupling assemblies for use with steam hoses rated for pressures up to 18 barPublic Comment
BS EN 16643 assemblies - Unbonded fluoroplastic lined (e. g. PTFE) hoses and hose assemblies for liquid and gaseous chemicals - SpecificationPublic Comment
BS EN 16811-1 Winter maintenance equipment - De-icing agents Part 1: Sodium chloride - Requirements and test methodsApproval
BS EN 16811-2 Winter maintenance equipment - De-icing agents Part 2: Calcium chloride and Magnesium chloride - Requirements and test methodsApproval
BS EN 16985 Safety requirementsAccepted
BS EN 1762 Rubber hoses and hose assemblies for liquefied petroleum gas, LPG (liquid or gaseous phase), and natural gas up to 25 bar (2,5 MPa) - SpecificationIdea
Opens a new windowBS EN 1765 Rubber hose assemblies for oil suction and discharge services - Specification for the assembliesApproval
BS EN 50628 50628 Erection of electrical installations in underground minesPublic Comment
BS EN 50632-2-11 Electric motor-operated tools - Dust measurement procedure - Part 2-11: Particular requirements for jig and sabre sawsApproval
BS EN 50632-2-14 Electric motor-operated tools - Dust measurement procedure - Part 2-14: Particular requirements for planersApproval
BS EN 50632-2-17 Electric motor-operated tools - Dust measurement procedure - Part 2-17: Particular requirements for routers and trimmersApproval
BS EN 50632-2-19 Electric motor-operated tools - Dust measurement procedure - Part 2-19: Particular requirements for jointersApproval
BS EN 50632-2-3 tools - Dust measurement procedure - Part 2-3: Particular requirements for concrete grinders and disk-type sandersApproval
BS EN 50632-2-4 tools - Dust measurement procedure - Part 2-4: Particular requirements for sanders other than disk typeApproval
BS EN 50632-2-5 Electric motor-operated tools - Dust measurement procedure - Part 2-5: Particular requirements for circular sawsApproval
BS EN 50632-3-1 Electric motor-operated tools - Dust measurement procedure - Part 3-1: Particular requirements for transportable table sawsApproval
BS EN 50632-3-3 Electric motor-operated tools - Dust measurement procedure - Part 3-3: Particular requirements for transportable planers and thicknessersPublic Comment
BS EN 50632-3-9 Electric motor-operated tools - Dust measurement procedure - Part 3-9: Particular requirements for transportable mitre sawsApproval
BS EN 60079-0 Ed 7.0 Explosive atmospheres Part 0: Equipment - General requirementsAccepted
BS EN 60079-10-1 Ed 2.0 Explosive atmospheres Part 10-1: Classification of areas - Explosive gas atmospheresApproval
BS EN 60079-13 Ed 2.0 Explosive atmospheres Part 13: Equipment protection by pressurized room p and artificially ventilated room vPublic Comment
BS EN 60079-14:2014/COR1:2016 BS EN 60079-14:2014/COR1:2016 Explosive atmospheres. Part 14: Electrical installations design, selection and erectionnull
BS EN 60079-15 Ed 5.0 Explosive atmospheres Part 15: Equipment protection by type of protection n NULLAccepted
BS EN 60079-2:2014/COR1:2015 Explosive Atmospheres Part 2 - Equipment protection by pressurized enclosure "p"null
BS EN 60079-29-1 Ed 2.0 Explosive atmospheres Part 29-1: Gas detectors - Performance requirements of detectors for flammable gasesPublic Comment
BS EN 60079-30-1 Explosive atmospheres Part 30-1: Electrical resistance trace heating- General; type testing and design requirementsPublication
BS EN 60079-30-2 Explosive atmospheres Part 30-2: Electrical resistance trace heating- Application guide for design; installation and maintenancePublication
BS EN 60204-1 ED 6.0 Safety of machinery - Electrical equipment of machines - Part 1: General requirementsPublic Comment
BS EN 60335-1 Ed 5.0 /A2 Household and similar electrical appliances - Safety Part 1: General requirementsApproval
BS EN 60335-1:2012+A1 Household and similar electrical appliances - Safety - Part 1: General requirementsPublication
BS EN 60335-2-107 Ed. 1.0/A1 Household and similar electrical appliances - Safety Part 2-107: Particular requirements for robotic battery powered electrical lawnmowersPublic Comment
BS EN 60335-2-11 Ed 7.0 /A2 Household and similar electrical appliances - Safety Part 2-11: Particular requirements for tumble dryersApproval
BS EN 60335-2-24/A2 Household and similar electrical appliances - Safety - Part 2-24: Particular requirements for refrigerating appliances, ice-cream appliances and ice makersApproval
BS EN 60335-2-24:2010+A1 Household and similar electrical appliances - Safety - Part 2-24: Particular requirements for refrigerating appliances, ice- cream appliances and ice-makersApproval
BS EN 60335-2-34/A1 Household and similar electrical appliances - Safety - Part 2-34: Particular requirements for motor-compressorsApproval
BS EN 60335-2-38:2003/A11 Household and similar electrical appliances - Safety - Part 2-38: Particular requirements for commercial electric griddles and griddle grillsAccepted
BS EN 60335-2-4:2010/A11 Household and similar electrical appliances - Safety - Part 2-4: Particular requirements for spin extractorsApproval
BS EN 60335-2-58:2005/A2 Household and similar electrical appliances - Safety - Part 2-58: Particular requirements for commercial electric dishwashing machinesPublication
BS EN 60335-2-7:2010/A2 Household and similar electrical appliances - Safety Part 2-7: Particular requirements for washing machinesApproval
BS EN 60335-2-89/A2 Household and similar electrical appliances - Safety - Part 2-89: Particular requirements for commercial refrigerating appliances with an incoporated or remote refrigerant unit or compressorPublication
BS EN 60335-2-89:2010+A1 Household and similar electrical appliances - Safety - Part 2-89: Particular requirements for commercial refrigerating appliances with an incorporated or remote refrigerant unit or compressorPublication
BS EN 61770: 2009/A1 to the water mains - Avoidance of backsiphonage and failure of hose-setsPublication
BS EN 62046 ED 1.0 Safety of Machinery – Application of protective equipment to detect the presence of personsPublication
BS EN 62745 Safety of machinery - Requirements for the interfacing of cableless controllers to machineryPublic Comment
BS EN 62841-2-10 Electric Motor-Operated Hand-Held Tools; Transportable Tools and Lawn and Garden Machinery - Safety Part 2-10: Particular requirements for hand-held mixersPublic Comment
BS EN 62841-2-11 Ed. 1.0 IEC 62841-2-11 Ed. 1 Electric Motor-Operated Hand-Held Tools,Transportable Tools and Lawn and Garden Machinery - Safety - Part 2-11: Particular requirements for hand-held reciprocating saws (jig and sabre saws)Approval
BS EN 62841-2-11:2015/AA Electric motor-operated hand-held tools, transportable tools and lawn and garden machinery - Safety - Part 2-11: Particular requirements for hand-held reciprocating saws (jig and sabre saws)Approval
BS EN 62841-2-14 Hand-Held Tools, Transportable Tools and Lawnand Garden Machinery - Safety - Part 2-14: Particular requirements for hand-held planersApproval
BS EN 62841-2-17 Electric motor-operated hand-held tools; transportable tools and lawn and garden machinery - Safety Part 2-17: Particular requirements for hand-held routersPublic Comment
BS EN 62841-2-2:2014 ELECTRIC MOTOR-OPERATED HAND-HELD TOOLS, TRANSPORTABLE TOOLS AND LAWNAND GARDEN MACHINERY – SAFETY – Part 2-9: Particular requirements for hand-held tappers and threadersnull
BS EN 62841-2-21 Electric motor-operated hand-held tools; transportable tools and lawn and garden machinery - Safety Part 2-21: Particular requirements for hand-held drain cleanersPublic Comment
BS EN 62841-2-4:2014 CORR HAND-HELD TOOLS, TRANSPORTABLE TOOLS AND LAWNAND GARDEN MACHINERY – SAFETY – ,, Part 2-4: Particular requirements for hand-held sanders and polishers other than disc type ,,null
BS EN 62841-2-8 Ed. 1.0 Electric Motor-Operated Hand-Held Tools, Transportable Tools and Lawnand Garden Machinery - Safety Part 2-8: Particular requirements for hand-held shears and nibblersApproval
BS EN 62841-2-9:2015 COR 1 ELECTRIC MOTOR-OPERATED HAND-HELD TOOLS, TRANSPORTABLE TOOLS AND LAWNAND GARDEN MACHINERY – SAFETY – ,, Part 2-9: Particular requirements for hand-held tappers and threaders ,,null
BS EN 62841-3-1:2014/COR1:2015 60079-14:2014/COR1:2016 Explosive atmospheres. Part 14: Electrical installations design, selection and erectionnull
BS EN 62841-3-10 Electric motor-operated hand-held tools, transportable tools and lawn and garden machinery - Safety Part 3-10: Particular requirements for transportable cut-off machinesPublication
BS EN 62841-3-10:2015/AA Electric Motor-Operated Hand-Held Tools, Transportable Tools and Lawn and Garden Machinery - Safety - Part 3-10: Particular requirements for transportable cut-off machinesApproval
BS EN 62841-3-12 Ed. 1.0 Electric Motor Operated Hand-Held Tools, Transportable Tools and Lawnand Garden Machinery - Safety - Part 3-12: Particular requirements for transportable threading machinesPublic Comment
BS EN 62841-3-13 Electric motor-operated hand-held tools; transportable tools and lawn and garden machinery - Safety Part 3-13: Particular requirements for transportable drillsPublic Comment
BS EN 62841-3-4 Ed. 1.0 Electric Motor Operated Hand-Held Tools, Transportable Tools and Lawnand Garden Machinery - Safety - Part 3-4: Particular requirements for transportable bench grindersApproval
BS EN 62841-3-9 Electric motor-operated hand-held tools, transportable tools and lawn and garden machinery - Safety Part 3-9: Particular requirements for transportable mitre sawsPublication
BS EN 62841-4-1 Ed. 1 Electric Motor-Operated Hand-Held Tools, Transportable Tools and Lawnand Garden Machinery - Safety - Part 4-1: Particular requirements for chain sawsPublic Comment
BS EN 62841-4-2 Ed1.0 Tools, Transportable Tools and Lawnand Garden Machinery - Safety - Part 4-2: Particular requirements for hedge trimmersPublic Comment
BS EN 62990-1 Workplace Atmospheres Part 1 Gas detectors - Performance requirements of detectors for toxic gasesAccepted
BS EN ENISO 16773-1 impedance spectroscopy (EIS) on high-impedance coated specimens Part 1: Terms and definitionsPublication
BS EN ENISO 16773-2 impedance spectroscopy (EIS) on high-impedance coated specimens Part 2: Collection of dataPublication
Opens a new windowBS EN ISO 12944-1 protection of steel structures by protective coating systems Part 1: General introductionPublic Comment
Opens a new windowBS EN ISO 12944-2 protection of steel structures by protective coating systems Part 2: Classification of environmentsPublic Comment
BS EN ISO 12944-3 protection of steel structures by protective coating systems Part 3: Design considerationsPublic Comment
Opens a new windowBS EN ISO 12944-7 protection of steel structures by protective coating systems Part 7: Execution and supervision of paint workPublic Comment
BS EN ISO 13854 Safety of machinery - Minimum gaps to avoid crushing of parts of the human bodyPublic Comment
BS EN ISO 2143 Estimation of loss of absorptive power of anodic oxidation coatings after sealing - Dye-spot test with prior acid treatmentAccepted
BS EN ISO 2931 Assessment of quality of sealed anodic oxidation coatings by measurement of admittanceAccepted
BS EN ISO 3210 Assessment of quality of sealed anodic oxidation coatings by measurement of the loss of mass after immersion in phosphoric acid/chromic acid solutionPublic Comment
BS EN ISO 7599 General specifications for anodic oxidation coatings on aluminiumAccepted
BS EN ISO/IEC 60079-13 IEC 60079-13 Explosive atmospheres Part 13: Equipment protection by pressurized room "p" and artificially ventilated room "v"Public Comment
BS EN WI 16820 assemblies for use in the pharmaceutical and biotechnological industry with hoses of non-metallic materials - Elastomeric hoses with or without liningPublic Comment
BS EN WI 16821 assemblies for use in the pharmaceutical and biotechnological industry with hoses of non-metallic materials - Silicone rubber hosePublic Comment
BS EN16330:2013/CORR Winter and road service area equipment - Power system and relatedcontrols - Power hydraulic system and electric interfacesPublication
BS ENISO 11997-1 resistance to cyclic corrosion conditions Part 1: Wet (salt fog)/dry/humidityPublic Comment
BS ENISO 1401 Rubber hoses for agricultural sprayingPublic Comment
BS ENISO 1514 Paints and varnishes - Standard panels for testingTechnical Review
BS ENISO 16773-3 Paints and varnishes - Electrochemical impedance spectroscopy (EIS) on high-impedance coated specimens Part 3: Processing and analysis of data from dummy cellsPublication
BS ENISO 16773-4 Paints and varnishes - Electrochemical impedance spectroscopy (EIS) on high-impedance coated specimens Part 4: Examples of spectra of polymer-coated specimensPublic Comment
BS ENISO 1825 aircraft ground fuelling and defuelling - SpecificationAccepted
BS ENISO 18752 Rubber hoses and hose assemblies - Wire- or textile reinforced single-pressure types for hydraulic applications - SpecificationApproval
BS ENISO 19598 coatings of zinc and zinc alloys on iron or steel with supplementary Cr(VI)-free treatmentPublic Comment
BS ENISO 20567-1 stone-chip resistance of coatings Part 1: Multi-impact testingPublic Comment
BS ENISO 20567-2 stone-chip resistance of coatings Part 2: Single-impact test with a guided impact bodyPublic Comment
BS ENISO 2081 Metallic and other inorganic coatings - Electroplated coatings of zincwith supplementary treatments on iron or steelPublic Comment
BS ENISO 2082 Metallic and other inorganic coatings -- Electroplated coatings ofcadmium with supplementary treatments on iron or steelPublic Comment
BS ENISO 2178 substrates - Measurement of coating thickness - Magnetic methodPublication
BS ENISO 2398 compressed air - SpecificationPublic Comment
BS ENISO 2811-1 Paints and varnishes - Determination of density Part 1: Pycnometer methodPublication
BS ENISO 3248 the effect of heatTechnical Review
BS ENISO 3949 Textile-reinforced types for hydraulic applications - SpecificationAccepted
BS ENISO 4623-2 resistance to filiform corrosion Part 2: Aluminium substratesTechnical Review
BS ENISO 4624 Paints and varnishes - Pull-off test for adhesionApproval
BS ENISO 4628-1 degradation of coatings - Designation of quantity and size of defects, and of intensity of uniform changes in appearance Part 1: General introduction and designation systemPublication
BS ENISO 4628-10 Paints and varnishes - Evaluation of degradation of coatings - Designation of quantity and size of defects, and of intensity of uniform changes in appearance Part 10: Assessment of degree of filiform corrosionPublication
BS ENISO 4628-2 Paints and varnishes - Evaluation of degradation of coatings - Designation of quantity and size of defects, and of intensity of uniform changes in appearance Part 2: Assessment of degree of blisteringPublication
BS ENISO 4628-3 Paints and varnishes - Evaluation of degradation of coatings - Designation of quantity and size of defects, and of intensity of uniform changes in appearance Part 3: Assessment of degree of rustingPublication
BS ENISO 4628-4 Paints and varnishes - Evaluation of degradation of coatings - Designation of quantity and size of defects, and of intensity of uniform changes in appearance Part 4: Assessment of degree of crackingPublication
BS ENISO 4628-5 Paints and varnishes - Evaluation of degradation of coatings - Designation of quantity and size of defects, and of intensity of uniform changes in appearance Part 5: Assessment of degree of flakingPublication
BS ENISO 4628-7 Paints and varnishes - Evaluation of degradation of coatings - Designation of quantity and size of defects, and of intensity of uniform changes in appearance Part 7: Assessment of degree of chalking by velvet methodPublication
BS ENISO 4641 water suction and discharge - SpecificationPublic Comment
BS ENISO 5774 for compressed-air applications - SpecificationPublication
BS ENISO 6134 saturated steam - SpecificationPublic Comment
BS ENISO 6802 assemblies with wire reinforcements - Hydraulic impulse test with flexingPublic Comment
BS ENISO 6803 assemblies - Hydraulic-pressure impulse test without flexingPublic Comment
BS ENISO 6806 in oil burners - SpecificationPublic Comment
BS ENISO 7233 assemblies - Determination of resistance to vacuumPublic Comment
BS ENISO 7326 ozone resistance under static conditionsPublic Comment
BS ENISO 7751 assemblies - Ratios of proof and burst pressure to maximum working pressurePublic Comment
BS ENISO 7784-1 Paints and varnishes - Determination of resistance to abrasion Part 1: Rotating abrasive-paper-covered wheel methodApproval
BS ENISO 7784-2 Paints and varnishes - Determination of resistance to abrasion Part 2: Rotating abrasive rubber wheel methodApproval
BS ENISO 7784-3 Paints and varnishes - Determination of resistance to abrasion Part 3: Method with abrasive-paper covered wheel and linearly reciprocating test panelApproval
BS ENISO 8028 assemblies for airless paint spraying - SpecificationPublic Comment
BS ENISO 8033 of adhesion between componentsPublic Comment
BS ENISO 8331 assemblies - Guidelines for selection, storage, use and maintenancePublic Comment
BS ENISO 9717 Phosphate conversion coating of metalsAccepted
BS IECIEC 62841-1:2014 C 2 60079-14:2014/COR1:2016 Explosive atmospheres. Part 14: Electrical installations design, selection and erectionnull
BS ISO 10074 Anodizing of aluminium and its alloys - Specification for hard anodic oxidation coatings on aluminium and its alloysAccepted
BS ISO 10216 Anodizing of aluminium and its alloys - Instrumental determination of image clarity of anodic oxidation coatings - Instrumental methodAccepted
BS ISO 11237 Rubber hoses and hose assemblies - Compact wire-braid-reinforced hydraulic types for oil-based or water-based fluids - SpecificationAccepted
BS ISO 11424 Rubber hoses and tubing for air and vacuum systems for internal-combustion engines - SpecificationPublic Comment
BS ISO 11759 Rubber hoses and hose assemblies for dispensing liquefied petroleum gases (LPGs) - SpecificationPublic Comment
BS ISO 12944-4 Paints and varnishes - Corrosion protection of steel structures by protective coating systems Part 4: Types of surface and surface preparationAccepted
BS ISO 12944-6 Paints and varnishes - Corrosion protection of steel structures by protective coating systems Part 6: Laboratory performance test methodsAccepted
BS ISO 12944-8 Paints and varnishes - Corrosion protection of steel structures by protective coating systems Part 8: Development of specifications for new work and maintenanceAccepted
BS ISO 12944-9 Paints and varnishes - Corrosion protection of steel structures by protective coating systems Part 9: Protective paint systems and laboratory performance test methods for offshore and related structuresAccepted
BS ISO 13775-2 Thermoplastic tubing and hoses for automotive use Part 2: Petroleum-based-fuel applicationsPublic Comment
BS ISO 14118 Safety of machinery - Prevention of unexpected start-upAccepted
BS ISO 1436 Rubber hoses and hose assemblies - Wire-braid-reinforced hydraulic types for oil-based or water-based fluids - SpecificationPublication
BS ISO 1436 Rubber hoses and hose assemblies - Wire-braid-reinforced hydraulic types for oil-based or water-based fluids - SpecificationAccepted
BS ISO 15110 Paints and varnishes - Artificial weathering including acidic depositionAccepted
BS ISO 16301 Rubber and plastics hoses and hose assemblies, wire- or textile-reinforced, for hydraulic jacks applications - SpecificationAccepted
BS ISO 18535 Diamond-like carbon films - Determination of friction and wear characteristics of diamond-like carbon films by ball-on-disc methodPublication
Opens a new windowBS ISO 19385 Rubber hoses and hose assemblies for Water Jetting or Water blasting applicationsPublic Comment
BS ISO 19396-1 Paints and varnishes - Determination of pH value Part 1: pH electrodes with glass membranePublic Comment
BS ISO 19396-2 Paints and varnishes - Determination of pH value Part 2: pH electrodes with ISFET technologyPublic Comment
BS ISO 19399 Paints and varnishes - Wedge-cut method for determination of film thickness (scribe and drill method)Public Comment
BS ISO 19403-1 Paints and varnishes - Wettability Part 1: Terminology and general principlesPublic Comment
BS ISO 19403-2 Paints and varnishes - Wettability Part 2: Determination of the surface free energy of solid surfaces by measuring the contact anglePublic Comment
BS ISO 19403-3 Paints and varnishes - Wettability Part 3: Determination of the surface tension of liquids using the pendant drop methodPublic Comment
BS ISO 19403-4 Paints and varnishes - Wettability Part 4: Determination of the polar and dispersive fractions of the surface tension of liquids from an interfacial tensionPublic Comment
BS ISO 19403-5 Paints and varnishes - Wettability Part 5: Determination of the polar and dispersive fractions of the surface tension of liquids from contact angles measurements on a solid with only a disperse contribution to its surface energyPublic Comment
BS ISO 19403-6 Paints and varnishes - Wettability Part 6: Measurement of dynamic contact anglePublic Comment
BS ISO 19403-7 Paints and varnishes - Wettability Part 7: Measurement of the contact angle on a tilt stage (roll-off angle)Public Comment
BS ISO 19487 Metallic and other inorganic coatings - Electrodeposited nickel-ceramics composite coatingPublic Comment
BS ISO 19718 Rubber and plastics hoses and hose assemblies, wire- or textile- reinforced, for hydraulic power units used in hydraulic tool applications - SpecificationPublic Comment
BS ISO 20266 Paints and varnishes - Determination of image clarity (degree of sharpness of reflected or transmitted image)Accepted
BS ISO 20523 Carbon based films - Classification and designationsIdea
BS ISO 2135 Anodizing of aluminium and its alloys - Accelerated test of light fastness of coloured anodic oxidation coatings using artificial lightAccepted
BS ISO 2360 Non-conductive coatings on non-magnetic electrically conductive basis materials - Measurement of coating thickness - Amplitude-sensitive eddy-current methodAccepted
BS ISO 3668 Paints and varnishes - Visual comparison of the colour of paintsPublic Comment
BS ISO 3862 Rubber hoses and hose assemblies - Rubber-covered spiral-wire-reinforced hydraulic types for oil-based or water-based fluids - SpecificationPublication
BS ISO 3862 Rubber hoses and hose assemblies - Rubber-covered spiral-wire-reinforced hydraulic types for oil-based or water-based fluids - SpecificationAccepted
BS ISO 4079 Rubber hoses and hose assemblies - Textile-reinforced hydraulic types for oil-based or water-based fluids - SpecificationAccepted
BS ISO 4081 Rubber hoses and tubing for cooling systems for internal-combustion engines - SpecificationPublic Comment
BS ISO 6804 Rubber and plastics inlet hoses and hose assemblies for washing-machines and dishwashers - SpecificationPublic Comment
BS ISO 8789 Rubber hoses and hose assemblies for liquefied petroleum gas in motor vehicles - SpecificationPublic Comment
PD CLC/TR 50417 Safety of household and similar electrical appliances - Interpretations related to European Standards in the EN 60335 seriesAccepted
PD IEC/TS 60079-32-1 Ed 1.0 /A1 Amendment 1: Explosive atmospheres Part 32-1: Electrostatic hazards; guidanceApproval
PD ISO/TR 22100-3 Safety of machinery - Relationship with ISO 12100 Part 3: Implementation of ergonomic principles in safety standardsAccepted
PD ISO/TS 19837 Safety of Machinery - Trapped Key Interlocking Devices Principles for design and selectionIdea

[ back to top ]

Published standards (36)

Sort by: Reference | Title | Status

Standard referenceNameStatus
BS EN 1953:2013Atomising and spraying equipment for coating materials. Safety requirementsCurrent
BS EN 1953:1998+A1:2009Atomizing and spraying equipment for coating materials. Safety requirementsWithdrawn
BS EN 50177:2006Automatic electrostatic spraying equipment for flammable coating powderWithdrawn
BS EN 50177:1997Automatic electrostatic spraying installations for flammable coating powderWithdrawn
BS EN 50176:1997Automatic electrostatic spraying installations for flammable liquid spraying materialWithdrawn
BS EN 13355:2004+A1:2009Coating plants. Combined booths. Safety requirementsCurrent
BS EN 12581:2005+A1:2010Coating plants. Machinery for dip coating and electrodeposition of organic liquid coating material. Safety requirementsCurrent
BS EN 12215:2004+A1:2009Coating plants. Spray booths for application of organic liquid coating materials. Safety requirementsCurrent
BS EN 12981:2005+A1:2009Coating plants. Spray booths for application of organic powder coating material. Safety requirementsCurrent
BS EN 13966-1:2003Determination of the transfer efficiency of atomising and spraying equipment for liquid coating materials - Flat panelsCurrent
BS EN 50050:2001Electrical apparatus for potentially explosive atmospheres. Electrostatic hand-held spraying equipmentWithdrawn
BS EN 50050:2006Electrical apparatus for potentially explosive atmospheres. Electrostatic hand-held spraying equipmentWithdrawn
BS EN 50050-1:2013Electrostatic hand-held spraying equipment. Safety requirements - Hand-held spraying equipment for ignitable liquid coating materialsCurrent
BS EN 50050-3:2013Electrostatic hand-held spraying equipment. Safety requirements - Hand-held spraying equipment for ignitable flockCurrent
BS EN 50050-2:2013Electrostatic hand-held spraying equipment. Safety requirements - Hand-held spraying equipment for ignitable coating powderCurrent
BS 6742-3:1990Electrostatic painting and finishing equipment using flammable materials - Electrostatic painting and finishing equipment using flammable materials. Specification for selection, installation and use of hand-held powder spray guns (energy limit of 5 mJ) and their associated apparatusWithdrawn
BS 6742-4:1990Electrostatic painting and finishing equipment using flammable materials - Electrostatic painting and finishing equipment using flammable materials. Specification for selection, installation and use of hand-held flock spray guns (energy limit of 0,24 mJ or 5 mJ) and their associated apparatusWithdrawn
BS 6742-2:1987Electrostatic painting and finishing equipment using flammable materials - Specification for selection, installation and use of hand-held paint spray guns (energy limit of 0,24 mJ) and associated apparatusWithdrawn
BS 6742-1:1987Electrostatic painting and finishing equipment using flammable materials - Electrostatic painting and finishing equipment using flammable materials. Specification for hand-held spray guns and associated apparatusWithdrawn
BS 2769-2-2.7:1984Hand-held electric motor-operated tools. Particular requirements - Specification for spray gunsWithdrawn
BS EN 12621:2006+A1:2010Machinery for the supply and circulation of coating materials under pressure. Safety requirementsCurrent
BS EN 12757-1:2005+A1:2010Mixing machinery for coating materials. Safety requirements - Mixing machinery for use in vehicle refinishingCurrent
BS EN ISO 1514:1997Paints and varnishes. Standard panels for testingWithdrawn
BS EN 28028:1993Rubber and/or plastics hose assemblies for airless paint spraying. SpecificationWithdrawn
BS EN ISO 8028:2000Rubber and/or plastics hose assemblies for airless paint spraying. SpecificationCurrent, Work in Hand
BS EN 50144-2-7:1996Safety of hand-held electric motor operated tools - Particular requirements for spray gunsWithdrawn
BS EN 50144-2-7:2001Safety of hand-held electric motor operated tools - Particular requirements for spray gunsWithdrawn
BS EN 50580:2012+A1:2013Safety of hand-held electric motor operated tools. Particular requirements for spray guns - Particular requirements for spray gunsCurrent
BS 2808:1969Specification for artists' water-colour brushes for local authoritiesCurrent
BS 3136-2:1972Specification for cold emulsion spraying machines for roads - Metric unitsCurrent
BS EN 50059:1991Specification for electrostatic hand-held spraying equipment for non-flammable material for painting and finishingCurrent, Work in Hand
BS 2992:1970Specification for painters' and decorators' brushes for local authorities and public institutions (excluding quality of fillings)Current
BS EN 50177:2009+A1:2012Stationary electrostatic application equipment for ignitable coating powders. Safety requirements Current
BS EN 50223:2015Stationary electrostatic application equipment for ignitable flock material. Safety requirementsCurrent
BS EN 50223:2010Stationary electrostatic application equipment for ignitable flock material. Safety requirementsWithdrawn
BS EN 50176:2009Stationary electrostatic application equipment for ignitable liquid coating material. Safety requirements Current

[ back to top ]

Recently Viewed
Need Help?

We are here to help you with any queries. Email us for help.

But first, why not view the Help Pages?