Skip to content
RSS feed for this category

Cooling systems & lubricating systems

Standards in development (45)

Sort by: Title | Status

Standard TitleStatus
BS EN 13765 Thermoplastic multi-layer (non-vulcanized) hoses and hose assemblies for the transfer of hydrocarbons, solvents and chemicals - SpecificationIdea
BS EN 13766 Thermoplastic multi-layer (non-vulcanized) hoses and hose assemblies for the transfer of liquid petroleum gas and liquefied natural gas - SpecificationIdea
BS EN 14423:2013/A1 Clamp type coupling assemblies for use with steam hoses rated for pressures up to 18 barPublic Comment
BS EN 16643 assemblies - Unbonded fluoroplastic lined (e. g. PTFE) hoses and hose assemblies for liquid and gaseous chemicals - SpecificationPublic Comment
BS EN 1762 Rubber hoses and hose assemblies for liquefied petroleum gas, LPG (liquid or gaseous phase), and natural gas up to 25 bar (2,5 MPa) - SpecificationAccepted
BS EN 1765 Rubber hose assemblies for oil suction and discharge services - Specification for the assembliesApproval
BS EN WI 00230337 Water quality - General requirements and performance test procedures for water monitoring equipment - Automated measuring devicesIdea
BS EN WI 00230340 Water quality - Guidance on field and laboratory procedures for quantitative analysis and identification of macro-invertebrates from inland surface watersIdea
BS EN WI 16820 assemblies for use in the pharmaceutical and biotechnological industry with hoses of non-metallic materials - Elastomeric hoses with or without liningPublic Comment
BS EN WI 16821 assemblies for use in the pharmaceutical and biotechnological industry with hoses of non-metallic materials - Silicone rubber hosePublic Comment
BS ENISO 1401 Rubber hoses for agricultural sprayingApproval
Opens a new windowBS ENISO 1825 aircraft ground fuelling and defuelling - SpecificationPublic Comment
BS ENISO 18752 Rubber hoses and hose assemblies - Wire- or textile reinforced single-pressure types for hydraulic applications - SpecificationApproval
BS ENISO 2398 compressed air - SpecificationApproval
Opens a new windowBS ENISO 3949 Textile-reinforced types for hydraulic applications - SpecificationPublic Comment
BS ENISO 4641 water suction and discharge - SpecificationApproval
BS ENISO 5667-6 Water quality - Sampling Part 6: Guidance on sampling of rivers and streamsPublication
BS ENISO 6134 saturated steam - SpecificationPublic Comment
BS ENISO 6802 assemblies with wire reinforcements - Hydraulic impulse test with flexingApproval
BS ENISO 6803 assemblies - Hydraulic-pressure impulse test without flexingApproval
BS ENISO 6806 in oil burners - SpecificationPublic Comment
BS ENISO 7233 assemblies - Determination of resistance to vacuumPublic Comment
BS ENISO 7326 ozone resistance under static conditionsApproval
BS ENISO 7751 assemblies - Ratios of proof and burst pressure to maximum working pressureApproval
BS ENISO 8028 assemblies for airless paint spraying - SpecificationPublic Comment
BS ENISO 8033 of adhesion between componentsApproval
BS ENISO 8331 assemblies - Guidelines for selection, storage, use and maintenanceApproval
Opens a new windowBS ISO 11237 Rubber hoses and hose assemblies - Compact wire-braid-reinforced hydraulic types for oil-based or water-based fluids - SpecificationPublic Comment
BS ISO 11424 Rubber hoses and tubing for air and vacuum systems for internal-combustion engines - SpecificationPublic Comment
BS ISO 11759 Rubber hoses and hose assemblies for dispensing liquefied petroleum gases (LPGs) - SpecificationPublic Comment
BS ISO 12103-3 Road vehicles - Test contaminants for filter evaluation Part 3: Soot aerosolIdea
BS ISO 13775-2 Thermoplastic tubing and hoses for automotive use Part 2: Petroleum-based-fuel applicationsApproval
BS ISO 1436 Rubber hoses and hose assemblies - Wire-braid-reinforced hydraulic types for oil-based or water-based fluids - SpecificationPublication
BS ISO 1436 Rubber hoses and hose assemblies - Wire-braid-reinforced hydraulic types for oil-based or water-based fluids - SpecificationPublic Comment
Opens a new windowBS ISO 16301 Rubber and plastics hoses and hose assemblies, wire- or textile-reinforced, for hydraulic jacks applications - SpecificationPublic Comment
BS ISO 16332 Road vehicles - Water separation efficiency of fuel filter systems for diesel engine applicationPublic Comment
BS ISO 19385 Rubber hoses and hose assemblies for Water Jetting or Water blasting applicationsPublic Comment
BS ISO 19718 Rubber and plastics hoses and hose assemblies, wire- or textile- reinforced, for hydraulic power units used in hydraulic tool applications - SpecificationPublic Comment
BS ISO 3862 Rubber hoses and hose assemblies - Rubber-covered spiral-wire-reinforced hydraulic types for oil-based or water-based fluids - SpecificationPublication
BS ISO 3862 Rubber hoses and hose assemblies - Rubber-covered spiral-wire-reinforced hydraulic types for oil-based or water-based fluids - SpecificationPublic Comment
BS ISO 4079 Rubber hoses and hose assemblies - Textile-reinforced hydraulic types for oil-based or water-based fluids - SpecificationPublic Comment
BS ISO 4081 Rubber hoses and tubing for cooling systems for internal-combustion engines - SpecificationApproval
BS ISO 4548-12 Methods of test for full-flow lubricating oil filters for internal combustion engines Part 12: Filtration efficiency using particle counting, and contaminant retention capacityPublic Comment
BS ISO 6804 Rubber and plastics inlet hoses and hose assemblies for washing-machines and dishwashers - SpecificationApproval
BS ISO 8789 Rubber hoses and hose assemblies for liquefied petroleum gas in motor vehicles - SpecificationPublic Comment

[ back to top ]

Need Help?

We are here to help you with any queries. Email us for help.

But first, why not view the Help Pages?