Skip to content
RSS feed for this category

Transmissions & suspensions

Standards in development (94)

Sort by: Title | Status

Standard TitleStatus
BS EN 13765:2010/A1 Thermoplastic multi-layer (non-vulcanized) hoses and hose assemblies for the transfer of hydrocarbons, solvents and chemicals — Specification/Amendment 1Approval
BS EN 14420-8:2013/A1 Hose fittings with clamp units Part 8: Symmetrical half coupling (Guillemin system)/Amendment 1Idea
BS EN 16643 assemblies - Unbonded fluoroplastic lined (e. g. PTFE) hoses and hose assemblies for liquid and gaseous chemicals - SpecificationPublic Comment
BS EN 1679 Reciprocating internal combustion engines - Safety - Compression ignition enginesAccepted
BS EN 61851-1 Ed 3.0 Electric vehicle conductive charging system Part 1: General requirementsPublic Comment
BS EN 61851-21 Ed 2.0 Review Report on IEC 61851-21 Ed. 1.0: Electric vehicle conductive charging system Part 21: Electric vehicle requirements for conductive connection to an a.c./d.c. supplyAccepted
BS EN 61851-21-1 Electric vehicle conductive charging system Part 21-1 Electric vehicle onboard charger EMC requirements for conductive connection to a.c./d.c. supplyAccepted
BS EN 61851-21-2 Electric vehicle conductive charging system Part 21-1: EMC requirments for OFF board electric vehicle charging systemsAccepted
BS EN 61851-22 Ed 2.0 Electric vehicle conductive charging system Part 22: a.c. electric vehicle charging stationAccepted
BS EN 61851-3-5 Electric vehicles conductive power supply system Part 3-5: Requirements for Light Electric Vehicles (LEV) communication - Pre-defined communication parametersAccepted
BS EN 61851-3-6 ELECTRIC VEHICLES CONDUCTIVE POWER SUPPLY SYSTEM Part 3-6; Requirements for Light Electric Vehicles (LEV) communication - Voltage converter unitAccepted
BS EN 61851-3-7 ELECTRIC VEHICLES CONDUCTIVE POWER SUPPLY SYSTEM Part 3-7; Requirements for Light Electric Vehicles (LEV) communication - Battery systemAccepted
BS EN 61980 Electric vehicle inductive charging systems Part 1 General requirementsPublic Comment
BS EN 62840-1 Ed1.0 Electric vehicle battery swap system Part 1: System description and general requirementsAccepted
BS EN 62840-2 ELECTRIC VEHICLE BATTERY SWAP SYSTEM Part 2: Safety requirementsAccepted
BS EN 853 Rubber hoses and hose assemblies - Wire braid reinforced hydraulic type - SpecificationTechnical Review
BS EN 854 Rubber hoses and hose assemblies - Textile reinforced hydraulic type - SpecificationTechnical Review
BS EN 856 Hose and hose assemblies - Rubber-covered spiral wire reinforced hydraulic type - SpecificationTechnical Review
BS EN 857 Hose and hose assemblies - Wire braid reinforced compact type for hydraulic applications - SpecificationTechnical Review
BS EN ISO 15007-1 Road vehicles - Measurement of driver visual behaviour with respect to transport information and control systems - Part 1: Definitions and parametersPublication
BS EN ISO 6806 Rubber hoses and hose assemblies for use in oil burners - SpecificationPublication
BS EN61980-2 Electric vehicle inductive charging systems Part 2 Manual connection system using paddleIdea
BS ENISO 15008 Road vehicles - Ergonomic aspects of transport information and control systems - Specifications and test procedures for in-vehicle visual presentationAccepted
BS ENISO 16231-2 Self-propelled agricultural machinery - Assessment of stability Part 2: Calculations and test proceduresPublic Comment
BS ENISO 17409 Electrically propelled road vehicles - Connection to an external electric power supply - Safety requirementsPublic Comment
BS ENISO 17962 Agricultural machinery - Seeding (planting) equipment - Considerations for minimizing the effects of fan exhaust from pneumatic systemsPublic Comment
BS ENISO 17989-1 Tractors and machinery for agriculture and forestry - Sustainability Part 1: PrinciplesPublic Comment
BS ENISO 28017:2011/Amd 1 Rubber hoses and hose assemblies, wire or textile reinforced, for dredging applications - Specification - Amendment 1Approval
BS ENISO 4254-14 Agricultural machinery - Safety Part 14: Mounted, semi-mounted and trailed bale wrappersPublic Comment
Opens a new windowBS ENISO 4254-7 Agricultural machinery - Safety Part 7: Combine harvesters, forage harvesters and cotton harvestersPublic Comment
BS ENISO 6134 saturated steam - SpecificationAccepted
BS ENISO 6802 assemblies with wire reinforcements - Hydraulic impulse test with flexingAccepted
BS ENISO 8528-13 engine driven alternating current generating sets Part 13: SafetyPublic Comment
BS ISO 10231:2003/AMD 1+A1 Motorcycles tyres - Test methods for verifying tyre capabilitiesPublic Comment
BS ISO 11759 Rubber hoses and hose assemblies for dispensing liquefied petroleum gases (LPGs) - SpecificationPublication
BS ISO 13050 Curvilinear toothed synchronous belt drive systemsApproval
BS ISO 13363 Rubber and plastics hoses for marine-engine wet-exhaust systems - SpecificationPublic Comment
BS ISO 13775-1 Thermoplastic tubing and hoses for automotive use Part 1: Non-fuel applicationsPublic Comment
BS ISO 13775-2 Thermoplastic tubing and hoses for automotive use Part 2: Petroleum-based-fuel applicationsAccepted
BS ISO 14960-1 Tubeless tyres - Valves and components Part 1: Test methodsPublication
BS ISO 14960-2 Tubeless tyres - Valves and components Part 2: Clamp-in tubeless tire valve-test methodPublication
BS ISO 16301 Rubber and plastics hoses and hose assemblies, wire- or textile-reinforced, for hydraulic jacks applications - SpecificationAccepted
BS ISO 16505 Road vehicles - Ergonomic and performance aspects of Camera-Monitor- Systems - Requirements and test procedures.Approval
Opens a new windowBS ISO 17464 Pneumatic tubes for automotive vehicles - Technical requirements and test methodsPublic Comment
BS ISO 17488 Road vehicle - Transport information and control systems - Detection-response Task (DRT) for assessing selective attention in drivingAccepted
BS ISO 17717 Meteorological balloons - SpecificationAccepted
BS ISO 18106 Truck and bus tyres - Methods for measuring snow grip performance - Loaded new tyresAccepted
BS ISO 1823.2 Rubber hose assemblies for oil suction and discharge service - SpecificationPublic Comment
BS ISO 18300 Electrically propelled road vehicles - Specifications for lithium-ion cell and battery coupled with other types of battery and capacitorPublic Comment
BS ISO 18804 Rims for agricultural, forestry and construction machinesPublic Comment
BS ISO 18805 Tyre classificationPublic Comment
BS ISO 18807 Tyres and rims for logging and forestry servicePublic Comment
BS ISO 18885-1 TPMS snap-in valves Part 1: IdentificationAccepted
BS ISO 18885-2 TPMS snap-in valves Part 2:Valve environmentAccepted
BS ISO 19013-2 Rubber hoses and tubing for fuel circuits for internal combustion engines - Specification Part 2: Gasoline fuelsPublic Comment
BS ISO 19346 Elastic belt drives - V-ribbed belts, PH, PJ, PK and PL profiles Determination of physical propertiesIdea
BS ISO 19347 Synchronous belt drives - belt and pulleysPublic Comment
BS ISO 19363 Electrically propelled road vehicles - Inductive wireless connection to an external electric power supply - Interoperability and Safety requirementsIdea
BS ISO 19425 Reciprocating internal combustion engines - Measurement method for air cleaners - Sound power level of combustion air inlet noise and insertion loss using sound pressureIdea
BS ISO 19447 Passenger car tyres - Method for measuring ice grip performance Loaded new tyresIdea
BS ISO 19718 Rubber and plastics hoses and hose assemblies, wire- or textile- reinforced, for hydraulic power units used in hydraulic tool applications - SpecificationAccepted
BS ISO 19940 Tyre Stiffness Index testing procedure for Passenger Extended Mobility tyresIdea
BS ISO 21750 Road vehicles - Safety enhancement in conjunction with tyre inflation pressure monitoringAccepted
BS ISO 23671 Passenger car tyres - Method for measuring relative wet grip performance - Loaded new tyresPublic Comment
BS ISO 2575:2010+A3 Road vehicles - Symbols for controls, indicators and tell-talesPublication
Opens a new windowBS ISO 2575:2010/Amd 5 Road vehicles - Symbols for controls, indicators and tell-tales - Amendment 5Approval
BS ISO 3006 Road vehicles - Passenger car wheels for road use - Test methodsAccepted
BS ISO 3006 Road vehicles - Passenger car wheels for road use - Test methodsPublic Comment
BS ISO 3894 Road vehicles - Wheels/rims for commercial vehicles - Test methodsPublic Comment
BS ISO 4000-1 Passenger car tyres and rims - Part 1: Tyres (metric series)Public Comment
BS ISO 4156-2:2005/COR 1D COR 1 Straight cylindrical involute splines - Metric module, side fit Part 2: DimensionsAccepted
BS ISO 4223-1 Definitions of some terms used in the tyre industry Part 1: Pneumatic tyresAccepted
BS ISO 4251-1 Tyres (ply rating marked series) and rims for agricultural tractors and machines - Part 1: Tyre designation and dimensions, and approved rim contours.Public Comment
BS ISO 4251-2 Tyres (ply rating marked series) and rims for agricultural tractors and machines - Part 2: Tyre load ratingsPublic Comment
BS ISO 4254-5 Agricultural machinery - Safety Part 5: Power-driven soil-working machinesAccepted
BS ISO 4254-8 Agricultural machinery - Safety Part 8: Solid fertilizer distributorsAccepted
BS ISO 4254-9 Agricultural machinery - Safety Part 9: Seed drillsAccepted
BS ISO 5772 Rubber hoses and hose assemblies for measured fuel dispensing - SpecificationPublic Comment
BS ISO 6469-1/AMD1 Electrically propelled road vehicles. Safety specifications On-board rechargeable energy storage system (RESS)null
BS ISO 6469-2/AMD1 Road vehicles. Safety specifications Vehicle operational safety means and protection against failuresnull
BS ISO 6469-4 Electrically propelled road vehicles - Safety specifications Part 4: Post crash electrical safety requirementsPublic Comment
BS ISO 7967-10 Reciprocating internal combustion engines - Vocabulary of components and systems Part 10: Ignition systemsPublication
BS ISO 7967-11 Reciprocating internal combustion engines - Vocabulary of components and systems Part 11: Fuel systemsPublication
BS ISO 7967-12 Reciprocating internal combustion engines - Vocabulary of components and systems Part 12: Emission Control systemsPublication
BS ISO 8528-7 Reciprocating internal combustion engine driven alternating current generating sets Part 7: Technical declarations for specification and designIdea
BS ISO 8528-8 Reciprocating internal combustion engine driven alternating current generating sets Part 8: Requirements and tests for low-power generating setsPublic Comment
BS ISO 8528-9 Reciprocating internal combustion engine driven alternating current generating sets Part 9: Measurement and evaluation of mechanical vibrationsIdea
BS ISO 9563 Belt drives - Electrical conductivity of antistatic endless synchronous belts - Characteristics and test methodPublic Comment
BS ISO/IEC 61851-22 ED2 Electric vehicle conductive charging system Part 22: A.C. electric vehicle charging stationAccepted
BS ISO/IEC 62752 In cable control and protectivedevice for mode 2 charging of electric road vehicles - (IC-RCD)Public Comment
PD IEC/TS 61851-3-1 Ed 1.0 Electric Vehicles conductive power supply system - Part 3-1: General Requirements for Light Electric Vehicles (LEV) AC and DC conductive power supply systemsAccepted
PD IEC/TS 61851-3-2 Ed 1.0 Electric Vehicles conductive power supply system - Part 3-2: Requirements for Light Electric Vehicles (LEV) DC off-board conductive power supply systemsAccepted
PD IEC/TS 61851-3-4 Ed 1.0 Electric Vehicles conductive power supply system - Part 3-4: Requirements for Light Electric Vehicles (LEV) communicationAccepted
PD ISO/PAS 19295 Electrically propelled road vehicles - Specification of voltage sub-classes for voltage class BIdea

[ back to top ]

Published standards (67)

Sort by: Reference | Title | Status

Standard referenceNameStatus
BS ISO 29802:2009All terrain (AT) tyres and rims. Symbol marked pneumatic tyres on 5 degrees tapered rims. Designation, dimension, marking and load ratingsCurrent
BS ISO 4107:2010Commercial vehicles. Wheelhub attachment dimensionsCurrent
BS AU 214-3:1988Gearbox flanges - Specification for dimensions for type S gearbox flanges for commercial vehicles and busesCurrent
BS AU 214-2:1988Gearbox flanges - Specification for dimensions for type A gearbox flanges for commercial vehicles and busesCurrent
BS 6765-4:1987Leisure accommodation vehicles. Caravans - Specification for undergearCurrent
BS ISO 4000-2:2007Passenger car tyres and rims - RimsCurrent, Work in Hand
BS ISO 4000-1:2010Passenger car tyres and rims - Tyres (metric series)Withdrawn
BS ISO 4000-1:2013Passenger car tyres and rims - Tyres (metric series)Current, Work in Hand
BS ISO 4000-2:2013Passenger car tyres and rims - RimsCurrent
BS ISO 4000-1:2007Passenger car tyres and rims - Tyres (metric series)Withdrawn
BS ISO 13988:2008Passenger vehicle wheels. Clip balance weight and rim flange nomenclature, test procedures and performance requirementsCurrent
BS AU 215-2:1987Power take offs (PTOs) - Specification for dimensions of side openings for commercial road vehiclesCurrent
BS AU 215-3:1988Power take offs (PTOs) - Specification for dimensions of connections for rear mounted power take offs for commercial road vehiclesCurrent
BS AU 215-1:1987Power take offs (PTOs) - Specification for dimensions for clearance envelope for commercial road vehiclesCurrent
BS ISO 10597:2012Road vehicles. Flat attachment fixing nuts for commercial vehicles. Test methodsCurrent
BS ISO 7141:2005Road vehicles. Light alloy wheels. Impact testCurrent
BS ISO 14400:2005Road vehicles. Wheels and rims. Use, general maintenance and safetyrequi rements and out-of-service conditionsCurrent
BS ISO 16833:2006Road vehicles. Wheels. Measurement of radial and lateral run-outCurrent
BS ISO 3894:2005Road vehicles. Wheels/rims for commercial vehicles. Test methodsCurrent, Work in Hand
BS ISO 11425:1996Rubber hoses and hose assemblies for automobile power-steering systems. SpecificationCurrent
BS AU 218:1987Specification for automotive synchronous belt drivesWithdrawn
BS AU 203a:1988Specification for dimensions of couplings between power take offs (PTOs) and ancillary driven units on commercial road vehiclesCurrent
BS 3092:1973Specification for main friction clutches, main power-take-off assemblies and associated attachments for internal combustion enginesCurrent
BS 3486-1:1962Specification for wheels for agricultural machinery, implements and trailers - Wheel and hub centre dimensions. Metric and inch unitsWithdrawn
BS 3486-2:1970Specification for wheels for agricultural machinery, implements and trailers - Tyre and rim sizesWithdrawn
BS 3486-3:1970Specification for wheels for agricultural machinery, implements and trailers - NutsWithdrawn
BS ISO 4209-2:2012Truck and bus tyres and rims (metric series) - RimsCurrent
BS ISO 9413:2012+A1:2012Tyre valves. Dimensions and designationCurrent
BS AU 50-4.4.1:1991Tyres and wheels. Rim profiles and dimensions. Agricultural tractor and machine rims - Specification for existing (inch) series rimsWithdrawn
BS AU 50-4.1.1a:2001Tyres and wheels. Rim profiles and dimensions. Car rims - Specification for metric series rims - Sub-section 1.1a: Specification for metric series rimsWithdrawn
BS AU 50-4.1.1:1995Tyres and wheels. Rim profiles and dimensions. Car rims - Specification for metric series rimsWithdrawn
BS AU 50-4.2.1:1995Tyres and wheels. Rim profiles and dimensions. Commercial vehicle rims - Specification for metric series rimsWithdrawn
BS AU 50-4.2.1a:2002Tyres and wheels. Rim profiles and dimensions. Commercial vehicle rims - Specification for metric series rims - Section 2: Commercial vehicle rims Subsection 2.1a: Specification for metric series rimsWithdrawn
BS AU 50-4.5.2:1996Tyres and wheels. Rim profiles and dimensions. Industrial vehicle rims - Specification for rim profiles and dimensions for metric series pneumatic tyres and solid tyres for pneumatic tyre rimsWithdrawn
BS AU 50-4.5.1:1995Tyres and wheels. Rim profiles and dimensions. Industrial vehicle rims - Specification for rim profiles and dimensions for code-designated series tyresCurrent
BS AU 50-4.6.2:1991Tyres and wheels. Rim profiles and dimensions. Motorcycle rims - Specification for metric series 100, 90, 80, 70 and 60 rimsWithdrawn
BS AU 50-4.3.1a:1998Tyres and wheels. Rim profiles and dimensions. Off-the-road rims - Specification for narrow and wide base off-the-road vehicle rimsWithdrawn
BS AU 50-1.0d:1998Tyres and wheels. Tyres - GeneralCurrent
BS AU 50-1-0c:1977Tyres and wheels. Tyres - GeneralWithdrawn
BS AU 50-1.8:1989Tyres and wheels. Tyres. - Code of practice for the storage of tyres, inner tubes and flapsCurrent
BS AU 50-1.4.5:1992Tyres and wheels. Tyres. Agricultural tractor and machine tyres - Specification for designations, dimensions and marking for metric series tyresWithdrawn
BS AU 50-1.1.4:1994Tyres and wheels. Tyres. Car tyres - Method of test for verifying tyre capabilitiesWithdrawn
BS AU 50-1.1.1a:1995Tyres and wheels. Tyres. Car tyres - Specification for metric series tyresWithdrawn
BS AU 50-1.1.1b:1996Tyres and wheels. Tyres. Car tyres - Specification for metric series tyresWithdrawn
BS AU 50-1.1.1c:2001Tyres and wheels. Tyres. Car tyres - Tyres (metric series)Withdrawn
BS AU 50-1.0.1:1999Tyres and wheels. Tyres. General - Method of test for measuring tyre uniformityCurrent
BS AU 50-1.5.5:1998Tyres and wheels. Tyres. Industrial vehicle tyres - Specification for solid tyres (metric series) for pneumatic tyre rims. Load ratingsCurrent
BS AU 50-3.1c:2001Tyres and wheels. Valves - Tyre valves. Dimensions and designationWithdrawn
BS AU 50-3.2a:2002Tyres and wheels. Valves - Tyre valve threads - Section 2a: Tyre valve threadsCurrent
BS AU 50-3.1e:2004Tyres and wheels. Valves - Dimensions, designation, valve pressure ratings by use and torque for clamp-in valvesWithdrawn
BS AU 50-3-1a:1985Tyres and wheels. Valves - Specification for valve dimensionsWithdrawn
BS AU 50-3.2:1977Tyres and wheels. Valves - Tyre valve threads 5V1, 5V2, 6V1 and 8V1Withdrawn
BS AU 50-3.3:1980Tyres and wheels. Valves - Tyre valve threads 9V1, 10V2, 12V1 and 13V1Withdrawn
BS AU 50-3.4a:1980Tyres and wheels. Valves - Tyre valve threads 8V2, 10V1, 11V1, 13V2, 15V1, 16V1, 17V1, 17V2, 17V3, 19V1 and 20V1Withdrawn
BS AU 50-3.5:1983Tyres and wheels. Valves - Dimensions for ISO core chamber No. 1 for tyre inflation valvesWithdrawn
BS AU 50-3.6:1982Tyres and wheels. Valves - Dimensions for ISO core chamber No. 2 for tyre inflation valvesWithdrawn
BS AU 50-2-7:1987Tyres and wheels. Wheels and rims - Code of practice for the selection and care of wheels for commercial vehiclesWithdrawn
BS AU 50-2.2a:1984Tyres and wheels. Wheels and rims - Specification for dimensions of wheel naves and hub centres for commercial vehiclesWithdrawn
BS AU 50-2.8a:1985Tyres and wheels. Wheels and rims - Code of practice for the selection and care of wheels for passenger cars (including caravans and light trailers)Current
BS AU 50-2.3:1994Tyres and wheels. Wheels and rims - Specification for road-wheel nuts, studs and bolts for commercial vehiclesCurrent
BS AU 50-2-1b:1980Tyres and wheels. Wheels and rims - Rim profiles and dimensions (including openings for valves)Withdrawn
BS AU 50-2-5b:1976Tyres and wheels. Wheels and rims - Road wheels manufactured wholly or partly of cast light alloy for passenger carsWithdrawn
BS AU 50-2.0b:2000Tyres and wheels. Wheels and rims - General (including vocabulary, designation and marking) - Section 0b: General (including vocabulary, designation and marking)Withdrawn
BS AU 50-2.7a:1995Tyres and wheels. Wheels and rims - Code of practice for the selection and care of tyres and wheels for commercial vehiclesCurrent
BS AU 50-2.5c:1996Tyres and wheels. Wheels and rims - Specification for road wheels manufactured wholly or partly of cast light alloy for passenger carsCurrent
PD ISO/TR 29846:2008Tyres, valves and tubes. kPa/psi equivalencies for inflation pressuresCurrent
BS ISO 3911:2004Wheels and rims for pneumatic tyres. Vocabulary, designation and markingCurrent

[ back to top ]

Recently Viewed
Need Help?

We are here to help you with any queries. Email us for help.

But first, why not view the Help Pages?