Skip to content
RSS feed for this category

Rotating machinery

Rotating machinery sub-categories (6)

Category Name
Components
General
Generating sets
Generators
Motors
Other

[ back to top ]

Standards in development (29)

Sort by: Title | Status

Standard TitleStatus
Opens a new windowBS EN 16128 Ophthalmic optics - Reference method for the testing of spectacle frames and sunglasses for nickel releaseAccepted
BS EN 1679 Reciprocating internal combustion engines - Safety - Compression ignition enginesAccepted
BS EN 60034-1 Ed 13.0 Rotating electrical machines Part 1: Rating and performanceAccepted
BS EN 60034-12 Ed 3.0 Rotating electrical machines Part 12: Starting performance of single-speed three-phase cage induction motorsAccepted
BS EN 60034-18-42 Rotating electrical machines Part 18-42: Qualification and acceptance tests for partial discharge resistant electrical insulation systems (Type II) used in rotating electrical machines fed from voltage convertersAccepted
BS EN 60034-19 Ed 2.0 Rotating electrical machines Part 19: Specific test methods for d.c. machines operating on rectifier-fed power supplies or other d.c. sourcesPublication
BS EN 60034-23 ED 1.0 Rotating electrical machines Part 23: Specification for the refurbishment of rotating electrical machinesAccepted
BS ENISO 10938 visual acuity measurements - Printed, projected and electronicPublic Comment
BS ENISO 8528-13 engine driven alternating current generating sets Part 13: SafetyPublic Comment
BS IEC 60034-27-3 Ed1.0 ED 1.0 Rotating electrical machines Part 27-3: Dielectric dissipation factor measurement on stator winding insulation of rotating electrical machinesApproval
BS ISO 19425 Reciprocating internal combustion engines - Measurement method for air cleaners - Sound power level of combustion air inlet noise and insertion loss using sound pressureIdea
BS ISO 6621-4 Internal combustion engines - Piston rings Part 4: General specificationsApproval
BS ISO 6624-2 Internal combustion engines - Piston rings Part 2: Half keystone rings made of cast ironPublic Comment
BS ISO 6624-4 Internal combustion engines - Piston rings Part 4: Half keystone rings made of steelPublic Comment
BS ISO 7967-10 Reciprocating internal combustion engines - Vocabulary of components and systems Part 10: Ignition systemsPublication
BS ISO 7967-11 Reciprocating internal combustion engines - Vocabulary of components and systems Part 11: Fuel systemsPublication
BS ISO 7967-12 Reciprocating internal combustion engines - Vocabulary of components and systems Part 12: Emission Control systemsPublication
BS ISO 8178-4 Reciprocating internal combustion engines - Exhaust emission measurement Part 4: Steady-state test cycles for different engine applicationsAccepted
BS ISO 8178-5 Reciprocating internal combustion engines - Exhaust emission measurement Part 5: Test fuelsPublic Comment
BS ISO 8178-7 Reciprocating internal combustion engines - Exhaust emission measurement Part 7: Engine family determinationPublic Comment
BS ISO 8178-8 Reciprocating internal combustion engines - Exhaust emission measurement Part 8: Engine group determinationPublic Comment
BS ISO 8528-7 Reciprocating internal combustion engine driven alternating current generating sets Part 7: Technical declarations for specification and designIdea
BS ISO 8528-8 Reciprocating internal combustion engine driven alternating current generating sets Part 8: Requirements and tests for low-power generating setsPublic Comment
BS ISO 8528-9 Reciprocating internal combustion engine driven alternating current generating sets Part 9: Measurement and evaluation of mechanical vibrationsIdea
PD CEN/TS WI 00250190 Guidance for European Structural Design of Glass Components.Idea
PD CLC/TS 60034-25 Rotating electrical machines Part 25: A.C. Motors when used in power drive systems - Application guid eAccepted
PD IEC/TS 60034-30-2 Ed 1.0 Rotating electrical machines Part 30-2: Efficiency classes of variable speed AC motors (IE-code)Accepted
PD IEC/TS 60034-32 Rotating electrical machines - Part 32: Measurement of stator end winding vibration at form wound windingsAccepted
PD ISO/TR 18476 Ophthalmic optics and instruments - Free form technology - Spectacle lenses and measurementAccepted

[ back to top ]

Recently Viewed
Need Help?

We are here to help you with any queries. Email us for help.

But first, why not view the Help Pages?