Skip to content
RSS feed for this category

Bushings

Standards in development (29)

Sort by: Title | Status

Standard TitleStatus
BS EN 50085-1:2005/PRAA Cable trunking systems and cable ducting systems for electrical installations Part 1: General requirementsApproval
BS EN 50125-1 Railway applications - Environmental conditions for equipment Part 1: Equipment on board rolling stockPublication
BS EN 50153 Railway applications - Rolling stock - Protective provisions relating to electrical hazardsApproval
BS EN 50155 Railway applications - Electronic equipment used on rolling stockIdea
BS EN 50180-1 and from 250 A to 3,15 kA for liquid filled transformersPublic Comment
BS EN 50180-2 Bushings above 1 kV up to 52 kV and from 250A to 3,15 kA for liquid filled transformers Part 2: Requirement for bushing componentsnull
BS EN 50180-3 Bushings above 1 kV up to 52 kV and from 250 A to 3,15 kA for liquid filled transformers Part 3: Requirement for bushing fixationsnull
BS EN 50343 Railway applications - Rolling stock - Rules for installation of cablingApproval
BS EN 50393 Test methods and requirements for accessories for use on distribution cables of rated voltage 0,6/1,0 (1,2) kVPublic Comment
BS EN 50405 Railway applications - Current collection systems - Pantographs, testing methods for contact stripsIdea
BS EN 50502 Railway applications - Rolling stock - Electric equipment in trolley buses - Safety requirements and connection systemsPublic Comment
BS EN 50626 Conduit systems buried underground for the protection and management of insulated electrical cables or communication cablesIdea
BS EN 60077-1 Ed. 2.0 Railway applications - Electric equipment for rolling stock Part 1: General service conditions and general rulesIdea
BS EN 60077-2 Ed. 2.0 Electric equipment for rolling stock Part 2: Electrotechnical components - General rulesIdea
BS EN 60310 ED 4.0 Railway applications - Traction transformers and inductors on board rolling stockPublic Comment
BS EN 61245 Artificial pollution tests on high-voltage insulators to be used on d.c systemAccepted
BS EN 61377 Ed. 2.0 Railway Applications - Rolling stock - Combined-testing of motors andtheir control systemAccepted
BS EN 61386-1 Conduit systems for cable management - Part 1: General requirementsApproval
BS EN 61534-1+A1 Powertrack systems Part 1: General requirements Amendment 1Approval
BS EN 61534-22 Powertrack systems Part 22: Particular requirements for powertrack systems intended for on floor or under floor installation.Accepted
BS EN 61914 Cable cleats for electrical installationsAccepted
BS EN 62231-1 Composite station post insulators for substations with ac voltages greater than 1 000 V up to 245 kV – Part 1: Dimensional, mechanical and electrical characteristicsPublic Comment
BS EN 62275 Cable management systems - Cable ties for electrical installationsApproval
BS EN 62609-1 Insulators for overhead lines - Composite line post insulators Part 1 - Definitions, End Fittings and Designationsnull
BS EN 62772 Composite hollow core station post insulators for substations with a.c. and d.c.voltages greater than 1 000 V - Definitions, test methods and acceptance criteriaAccepted
BS EN 65700-19-03 Bushings for DC applicationApproval
BS IEC 61534-21 ED 2.0 POWERTRACK SYSTEMS – Part 21: Particular requirements for powertrack systems intended for wall and ceiling mountingApproval
PD IEC/TS 60815-4 ED 1.0 Selection and dimensioning of high-voltage insulators intended for usein polluted conditions - Part 4: Insulators for d.c. systemsIdea
PD IEC/TS 62073 Guidance on the measurement of hydrophobicity of insulator surfaces Part 2: Faults and switchingAccepted

[ back to top ]

Published standards (18)

Sort by: Reference | Title | Status

Standard referenceNameStatus
BS EN 50387:2002Busbar bushings up to 1 kV and from 1,25 kA to 5 kA, for liquid filled transformersCurrent
BS 7877:1999Busbar bushings up to 1 kV and from 1,25 kA to 5 kA, for liquid filled transformersWithdrawn
BS EN 50180:1999Bushings above 1 kV up to 36 kV and from 250 A to 3,15 kA for liquid filled transformersWithdrawn
BS EN 50180:2010Bushings above 1 kV up to 52 kV and from 250 A to 3,15 kA for liquid filled transformersCurrent, Work in Hand
BS EN 62199:2004Bushings for D.C. applicationCurrent
BS EN 50336:2002Bushings for transformers and reactor cable boxes not exceeding 36 kVCurrent
BS EN 50262:1999Cable glands for electrical installationsWithdrawn
BS EN 62444:2013Cable glands for electrical installationsCurrent
BS EN 60137:1996Insulated bushings for alternating voltages above 1 kVWithdrawn
BS EN 60137:2008Insulated bushings for alternating voltages above 1000 VCurrent
BS EN 60137:2003Insulated bushings for alternating voltages above 1000 VWithdrawn
BS 6121-5:2005Mechanical cable glands - Code of practice for selection, installation and inspection of cable glands and armour glandsCurrent
BS EN 50243:2002Outdoor bushings for 24 kV and 36 kV and for 5 kA and 8 kA, for liquid filled transformersCurrent
BS EN 50181:1999Plug-in type bushings above 1 kV up to 36 kV and from 250 A to 1.25 kA for equipment other than liquid filled transformersWithdrawn
BS EN 50181:2010Plug-in type bushings above 1 kV up to 52 kV and from 250 A to 2,50 kA for equipment other than liquid filled transformersCurrent
DD CLC/TS 50537-1:2010Railway applications. Mounted parts of the traction transformer and cooling system - HV bushing for traction transformersCurrent
BS 223:1985Specification for bushings for alternating voltages above 1000 VWithdrawn
BS 7616:1993Specification for bushings for liquid filled transformers above 1 kV and up to 36 kVWithdrawn

[ back to top ]

Recently Viewed
Need Help?

We are here to help you with any queries. Email us for help.

But first, why not view the Help Pages?